How To Install Crown Molding The Best Way

Crown molding isn't the easiest thing to install. That'due south why hiring a professional person is a good thought. This is always an selection and information technology'south a good one as well! You can have crown molding installed for a relatively low price compared to other contracting jobs.

However, if you are feeling assuming and believe that you tin take on the job of installing crown molding, so we can assist you with that. This guide will have yous through the steps and give yous tips along the way.

What Is Crown Molding?

Crown molding is a type of ornamental molding used forth interior walls and ceilings. It looks high-terminate and can cover any gaps or imperfections in the expanse where the ceiling meets the wall. But not all molding is created equally.

Any trim tin can do this besides , but crown molding is special. It uses a specific course and technique that is as old as the crown molding itself. Permit's take a look at how you can achieve the expect on your own.

How To Install Crown Molding

Installing crown molding doesn't always need to be done past a professional. You can install information technology on your own. While information technology isn't easy and shouldn't exist a beginner'south project, you tin can install information technology by following these steps.

Step 1: Test the crown molding

It'southward a skillful idea to buy a few samples of crown molding earlier you buy all that you need. You lot can secure them together and hold them to the ceiling to attempt dissimilar types out and find what you similar all-time.

Stride ii: Mensurate, Measure out the ceiling for crown molding

I say measure out twice because it is a good idea to always measure twice as much every bit yous cut. Then first off, get some grid newspaper and make a diagram of your room, using each foursquare as one square foot of infinite.

Write downwards the length of each wall, door, and walkway in the room where it is located on the newspaper. This is when yous figure how much molding you demand. Apply linear foot to calculate how much you demand.

Stride 3: Find The Right Pieces

Go to the shop and find the molding you lot chose later getting samples. Then, look at each slice advisedly so you don't end up with any pieces with imperfections. Make sure yous get enough for your entire room.

There's a good chance you volition have a few actress feet. This is okay. It'southward normal when the molding is sold in pieces rather than in linear human foot alone.

Step 4: Gear up

Now is a good time to purchase a miter saw and brad nailer. You desire to get everything you lot need from the hardware shop in one trip. If you don't desire to spend money on these things, then rent them instead.

Step 4: Mark The Wall

You demand to mark your ceilings and walls at this point. It depends on the size of your molding but there will be a mark on the ceiling, wall, and corner. Employ a chalk line or pencil to mark them, ensuring the lines are straight.

Stride 5: Install The Beginning Lath

The affair near crown molding is that now you lot can get information technology in single pieces. But most crown molding volition come in three pieces. Two baseboards or stops and and then the crown molding slice which is installed diagonally.

You want to make sure baseboards are installed first. Then go ahead and install them beyond the wall. They are easy to install and volition help secure the crown molding, giving them the crown look.

Step half dozen: Install Ceiling Runway

The ceiling rails are usually angled to assistance you lot get the correct angle on the crown molding. They are normally installed at about 45-degrees, just this is up to preference. Just brand sure you practice a test with the sample starting time.

Because of the angle, they usually need to be glued earlier you screw or smash them in. You can identify brackets with nails or screws to concur the angle while the glue is drying as well.

Stride 7: Install The Molding

Now comes the fun part. The molding needs to exist cutting at an angle on each corner. This is what the miter saw is here for. And so acquire how to make angles and utilise the miter saw before y'all begin cutting your precious molding.

The placement should be fairly obvious. It'southward a adept idea to have someone who knows what they are doing on mitt during this footstep considering it is important every bit it will be the almost eye-catching function of the molding.

Step viii: Sanding And Painting

At present it's time to finish up. Yous can get-go by sanding downwardly the molding if it is wood. And then fill the nail holes with woods filler. Permit information technology dry out before starting to paint or stain your crown molding your chosen color.

Make certain you protect your walls and ceiling with painter's tape. If you are painting your walls too, paint them before you install the molding. If yous do it subsequently, then paint the molding get-go.

DIY Crown Molding Tips And Tricks

Now that you know the basics of crown molding installation, you tin can now go down to business and learn a few tricks as well. These tips can assist you when you are installing your crown molding and subsequently.

Customize Your Crown Molding

You lot tin actually mix and match crown molding to create your own. Y'all tin can even cut your own if y'all know how to do it. This takes a lot of practice but you tin "mold" your ain molding with the correct tools.

This is similar to wood carving but isn't commonly done past manus. When you make your own crown molding, yous can even carve piddling designs into the molding. These are very expensive and sell for a lot of coin.

Store In-Shop

Because checking each piece of molding is of import, pick out your pieces in the shop. Even if y'all accept them shipped to your house or delivered. Enquire them to send you the exact pieces y'all choice out. Most hardware stores volition comply.

You lot tin can buy online or have them deliver any pieces. But they will usually pick off the top. Or worse, choice the pieces that they can't sell in the store. Then yes, finding your own pieces is always all-time.

Study The Crown Molding Blueprint

Before you begin, it's a bang-up idea to written report the crown molding design. At that place volition be three to 5 pieces unless you but already put together crown molding. Simply even if y'all exercise, learning the diagram can assistance you.

You will have a film of what the inside will look like, or at least should await like, which can assist you become the right angles and make the right cuts. Visualizing is of import when it comes to structure.

Mark Your Miter

When cutting angles, y'all need to mark your miter with a pencil before you even brainstorm to cutting. It's easy to become flipped effectually or upside downwardly so ever mark the board on the side that you can come across when testing it out.

So, you tin mark the side you will cut on likewise. Whether yous cutting on the forepart or the dorsum. Just make certain you lot don't mark the angle wrong or you will end upward with a piece of crown molding you may not be able to use at all.

Don't Forget To Caulk

Caulk tin can be just equally useful equally a wood filler. For any gaps that won't be visible but need to exist filled, caulk can work wonders. Simply use information technology along the edge and between any slice that isn't touching and you won't fifty-fifty notice information technology!

Caulk is an important textile and should always be kept on hand if you are doing whatever type of home interior or construction work. Make sure y'all have multiple different kinds and don't open up them until you are fix to use them.

Don't Overdo It On Nails

Nails can make you feel as if your crown molding is extra secure, but add too many and it does ii harmful things. First of all, too many nails tin really touch the forest filling, which becomes complicated.

Simply it can also touch on the structural integrity of your crown molding. Too many or one in the wrong identify and information technology can easily split. So avoid this by but placing nails where they need to be placed to secure the boards.

Stay 45-Degrees

Try to proceed angles at 45-degrees. Effort your first 45-degree fit by cutting two boards to fit. If they don't fit right, then in that location'south a problem with your ceiling or wall, non your molding. Because two angles should fit together.

If this is a problem, effort to cheque the levelness of your ceiling and wall. If this is the trouble, you lot'll demand to rent a professional to level it out or install your crown molding for you. Hopefully, yous don't face this issue!

Larn To Cope

Coping is a manner to employ a miter saw to cut the crown molding at an bending. But non just in the way you assume but also to create a lip that will let the crown molding pass over the other piece to create an even tighter fit.

This will all but eliminate gaps and await much better. It takes a lot of practice but if y'all do any woodworking then you will be able to learn this trick fairly easily. It will make all of the difference in the world!

Become Exact Measurements

Once again, measure, measure out, measure out! Get your measurements correct not by measuring right the first time but besides by ensuring that y'all measure multiple times. Make certain the measuring tape is always straight besides.

If information technology bumps or bends then the measurement won't be accurate. This doesn't matter in some cases but it sure does thing a lot when it comes to crown molding. Every millimeter counts, then try your best to get it right.

gillumnorted.blogspot.com

Source: https://www.homedit.com/crown-molding/